Step
| Action
| Value(s)
| Yes
| No
|
1
| Check if DTC B 3268 and DTC B 3267 is set in the BCM.
Refer to
Diagnostic System Check - Body Control System
in body control system.
Is DTC B 3268 and DTC B 3267 set in the BCM?
| --
| Go to
DTC B3267 Decklid Output Relay Short to GND/Open
or Go to
DTC B3268 Decklid Output Relay Short to BATT
in Body Control Systems
|
Go to Step 2
|
2
| Was the Rear Compartment Lid Release System Check performed?
| --
|
Go to Step 3
| Go to
Rear Compartment Lid Release System Check
|
3
| Activate the power door lock switch in one direction and then in the
other direction.
Do the door locks activate?
| --
|
Go to Step
4
|
Go to Step 14
|
4
|
- With a test light, connect between the rear compartment lid release
relay terminal C2 and B+.
- Using a Tech 2, activate the rear compartment lid lock release
actuator.
Does the test light illuminate?
| --
|
Go to Step
6
|
Go to Step 5
|
5
|
- With a test light ,backprobe between the BCM connector C2
terminal B12 and B+.
- Using a Tech 2, activate the rear compartment lid lock release
actuator.
Does the test light illuminate?
| --
|
Go to Step
16
|
Go to Step 10
|
6
|
- With a test light ,backprobe between the rear compartment lid
lock release actuator connector terminal A and terminal B.
- Using a Tech 2, activate the rear compartment lid lock release
actuator.
Does the test light illuminate?
| --
|
Go to Step
11
|
Go to Step 7
|
7
| With a test light ,connect between the rear compartment lid lock release
actuator terminal B and B+.
Does the test light illuminate?
| --
|
Go to Step
8
|
Go to Step 14
|
8
| With a test light ,connect between the rear compartment lid release
relay connector terminal C1 and ground.
Does the test light illuminate?
| --
|
Go to Step
9
|
Go to Step 15
|
9
|
- Using a 5 A fused jumper, connect between the rear compartment
lid release relay terminal C1 and terminal A2.
- With a test light ,connect between the rear compartment lid lock
release actuator terminal A and ground.
Does the test light illuminate?
| --
|
Go to Step
12
|
Go to Step 17
|
10
|
- Replace the BCM. Refer to
Body Control Module Replacement
in Body Control Systems for service
procedure.
- Perform the new BCM setup procedure. Refer to
Body Control Module (BCM) Programming/RPO Configuration
in Body Control
Systems for service procedure.
Is the repair complete?
| --
| Go to
Rear Compartment Lid Release System Check
| --
|
11
| Replace the rear compartment lid lock release actuator.
Refer to
Release Actuator Replacement
for service procedure.
Is the repair complete?
| --
| Go to
Rear Compartment Lid Release System Check
| --
|
12
| Replace the rear compartment lid release relay.
Is the repair complete?
| --
| Go to
Rear Compartment Lid Release System Check
| --
|
13
| Repair the short to B+ in circuit 1540.
Is the repair complete?
| --
| Go to
Rear Compartment Lid Release System Check
| --
|
14
| Repair the open in circuit 350.
Is the repair complete?
| --
| Go to
Rear Compartment Lid Release System Check
| --
|
15
| Repair the open in circuit 1540.
Is the repair complete?
| --
| Go to
Rear Compartment Lid Release System Check
| --
|
16
| Repair the open in circuit 253.
Is the repair complete?
| --
| Go to
Rear Compartment Lid Release System Check
| --
|
17
| Repair the open in circuit 56.
Is the repair complete?
| --
| Go to
Rear Compartment Lid Release System Check
| --
|
