The body control module (BCM) supplies a voltage reference through the instrument panel (I/P) dimming voltage reference circuit to the interior lamp dimmer switch, which is part of the headlamp switch. When the dimmer switch is placed in a desired brightness position, reference voltage is applied through the dimmer switch rheostat and the I/P lamps dimmer switch signal circuit to the BCM. The BCM interprets this voltage signal, then applies a pulse width modulated (PWM) voltage through the instrument panel lamp supply voltage circuit and the LED dimming supply circuit illuminating the LED and I/P panel lamps.

Schematic Reference

Interior Lights Dimming Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Interior Lighting Systems Description and Operation

Electrical Information Reference

Scan Tool Reference

Control Module References for scan tool information

1. Ignition ON, observe the driver door switch while commanding the Driver Door Switch Integrated Sw. Backlighting Test ON and OFF with a scan tool. The switch backlighting should turn ON and OFF between commanded states.

⇒	If the backlighting does not turn On and OFF or remains ON, replace the driver door switch.

2. Observe the driver heated and cooled seat switch while commanding the Driver Door Switch Non-Integrated Sw. Backlighting Test ON and OFF with a scan tool. The switch backlighting should turn ON and OFF between commanded states.

⇒	If the backlighting does not turn On and OFF or remains ON, refer to Front Door Switch Backlighting Malfunction.

3. Observe the passenger door switch while commanding the Passenger Door Switch Integrated Sw. Backlighting Test ON and OFF with a scan tool. The switch backlighting should turn ON and OFF between commanded states.

⇒	If the backlighting does not turn On and OFF or remains ON, replace the passenger door switch.

4. Observe the passenger heated and cooled seat switch while commanding the Passenger Door Switch Non-Integrated Sw. Backlighting Test ON and OFF with a scan tool. The switch backlighting should turn ON and OFF between commanded states.

⇒	If the backlighting does not turn On and OFF or remains ON, refer to Front Door Switch Backlighting Malfunction.

5. Observe the scan tool Dimming Control Signal parameter while operating the dimmer switch from high to low. The parameter should change from a high percent to a low percent as the switch is rotated.

⇒	If the parameter does not change, refer to Dimmer Switch Malfunction.

⇒	If the scan tool dimmer control operates normal, refer to Interior Backlighting Malfunction.

Dimmer Switch Malfunction

1. Ignition OFF, disconnect the harness connector at the headlamp switch.
2. Verify that a test lamp illuminates between the ground circuit terminal 8 and B+.

⇒	If the test lamp does not illuminate, test the ground circuit for an open/high resistance.

3. Verify the scan tool Dimming Control Signal parameter is less than 0.1 volts.

⇒	If greater than the specified range, test the signal circuit terminal 13 for a short to voltage. If the circuit tests normal, replace the BCM.

4. Test for B+ between the I/P dimming voltage reference circuit terminal 15 and ground.

⇒	If less than the specified value, test the voltage reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.

5. Install a 3A fused jumper wire between the signal circuit terminal 13 and the voltage reference circuit terminal 15. Verify the scan tool BCM Dimming Control Signal parameter is greater than 2.6 volts.

⇒	If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.

6. If all circuits test normal, test or replace the headlamp switch.

Interior Backlighting Malfunction

1. Ignition OFF, disconnect the harness connector at the component with the inoperative backlighting.
2. Test for less than 5 ohms between the appropriate ground circuit terminal listed below and ground.

•	Headlamp switch terminal 8

•	Hazard switch terminal B

•	IPC terminal 6

•	Ashtray lamp terminal B

•	HVAC control module terminal 11 X1

•	Radio terminal 8 X1

•	Driver information display switch terminal 5

•	Traction control switch terminal A

•	Reverse lockout solenoid terminal D X2

•	Garage door opener transmitter terminal 3

•	Sunroof switch terminal 5

•	Left rear door window switch terminal F

•	Right rear door window switch terminal F

•	Right steering wheel control switch terminal 1

•	Left steering wheel control switch terminal 8

⇒	If greater than the specified range, test the ground circuit for an open/high resistance.

3. Connect a test lamp between the appropriate control circuit terminal listed below and ground.

Incandescent Dimming

•	Headlamp switch terminal 7

•	Hazard switch terminal A

•	IPC terminal B

•	Ashtray lamp terminal A

•	Traction control switch terminal D

•	Reverse lockout solenoid terminal C X2

•	Garage door opener transmitter terminal 2

•	Sunroof switch terminal 3

•	Left rear door window switch terminal B

•	Right rear door window switch terminal B

LED Dimming

•	HVAC control module terminal 2 -- (X2 with C67) or (X3 with CJ2)

•	Radio terminal 7 X1

•	Driver information display switch terminal 4

•	Right steering wheel control switch terminal 2

•	Left steering wheel control switch terminal 6

4. Ignition ON, command the appropriate Incandescent Dimming or LED Dimming ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.

⇒	If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM

⇒	If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the BCM.

5. If all circuits test normal, test or replace the component with the inoperative backlighting.

Front Door Switch Backlighting Malfunction

1. Ignition OFF, disconnect the harness connector at the inoperative heated and cooled seat switch.
2. Verify that a test lamp illuminates between the appropriate low reference circuit terminal listed below and B+.

•	Driver heated and cool seat switch terminal 3

•	Passenger heated and cool sSeat switch terminal 5

⇒	If the test lamp does not illuminate, test the low reference circuit for an open/high resistance.

3. Connect a test lamp illuminates between the control circuit terminal listed below and ground.

•	Driver heated and cool seat switch terminal 5

•	Passenger heated and cool seat Sswitch terminal 3

4. Ignition ON, command the appropriate Driver or Passenger Door Switch Non-Integrated Backlighting Test ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.

⇒	If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the door switch.

⇒	If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the door switch.

5. If all circuits test normal, test or replace the heated and cooled seat switch.

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.