GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Buick 🢒 2001 🢒 Park Avenue 🢒 Engine 🢒 Engine Electrical 🢒 Cuts Out, Misses

Checks

Action

DEFINITION: Steady pulsation or jerking that follows engine speed, usually more pronounced as engine load increases.

Preliminary

Refer to Diagnostic System Check - Engine Controls .

    • Refer to Important Preliminary Checks in Symptoms - Engine Controls .
    • Refer to Visual/Physical Checks in Symptoms - Engine Controls .
    • Search for bulletins.

Fuel System
    • Check system fuel pressure. Refer to Fuel System Diagnosis .
    • Check for contaminated fuel. Refer to Alcohol/Contaminants-in-Fuel Diagnosis .
    • Check items which can cause an engine to run rich (Long Term FT significantly in the negative range). Refer to Diagnostic Aids for DTC P0171 .
    • Check items that can cause an engine to run lean (Long Term FT significantly in the positive range). Refer to Diagnostic Aids for DTC P0172 .
    • Check for fuel in the fuel pressure regulator vacuum hose.

Sensor/System
    • Check for conditions which cause an incorrect idle speed:
       - Throttle body tampering, excessive deposits, or damage.
       - Restricted air intake system. Refer to Air Intake System Description .
       - Large vacuum leak
    • Check the throttle position (TP) sensor and related circuit wiring. Refer to DTC P0123 .
    • Check the exhaust gas recirculation (EGR) system for proper operation. Refer to Exhaust Gas Recirculation (EGR) System Description .
    • Check the positive crankcase ventilation (PCV) valve for proper operation.
    • Check the transaxle range switch input with the vehicle in drive and the gear selector in drive or overdrive. Refer to Diagnostic Starting Point - Automatic Transmission in Automatic Transaxle.
    • Check the following for damage:
       - Bent harmonic balancer interrupter rings
       - Damaged crankshaft position (CKP) sensor

Ignition System
    • Check for proper ignition voltage output using the following steps:
       - Clip the J 26792 Spark Tester to engine ground.
       - Connect one end of a spark plug wire to the spark tester. Leave the other end of the spark plug wire connected to the coil being tested.
       - Connect another spark plug wire between the remaining tower of the coil being tested and ground.
       - Crank the engine while observing the spark tester, a spark should be observed.
       - Repeat the above steps for each coil.
    • If spark is not present at the coils, check for the following conditions:
       - Coils--Cracks, carbon tracking/arcing, or a secondary resistance value outside the specified range.

Coil Resistance
5,000-8,000 ohms

       - Spark plug wires--Signs of arcing/cross firing, cracks, carbon tracking, plug boot damage, pinched, improper routing, or a resistance value outside the specified range.

Spark Plug Wire Resistance
9,840 ohms per meter (3,000 ohms per ft)

   Important: Spraying the secondary ignition wires with a light mist of water may help locate an intermittent condition. Ignition components will arc to ground when a secondary component is faulty.

       - Defective module
       - Ignition system wiring--Loose ignition module feed or ground connection, or damaged system wiring.
    • Remove spark plugs and check for the following:
       - Fouled plugs
       - Cracks

   Important: If carbon tracking is detected on a component, replace that component and its mate.

       - Check the spark plugs for carbon tracking on the porcelain and pitting on the plug wire contact.
       - Improper gap
       - Burned or damaged electrodes
       - Improper heat range or reach
       - Refer to Maintenance Items in Maintenance and Lubrication.
    • If spark plugs are gas or oil fouled, the cause of the fouling must be determined before replacing the spark plugs.
    • Check for the following intermittent ignition system conditions:
       - Intermittent crankshaft position (CKP) 18X signal
       - Intermittent ignition feed circuit or sensor ground circuit to the crankshaft position sensor or the camshaft position sensor.
       - Intermittent 3X reference signal
       - Intermittent camshaft position (CMP) signal

Engine Mechanical
    • Check engine mechanical for the following:
       - Check compression
       - Sticking or leaking valves
       - Worn camshaft lobes
       - Valve timing
       - Bent push rods
       - Worn rocker arms
       - Broken valve springs
       - Excess oil in combustion chamber--Inspect for leaking valve seals
       - Low cylinder compression
    • Inspect for incorrect engine parts, such as the following basic components:
       - Camshaft
       - Cylinder heads
       - Pistons, etc.
    • Refer to Symptoms - Engine Mechanical in Engine Mechanical.

Additional Checks
    • Check exhaust system for possible restrictions. Check for the following:
       - Inspect exhaust system for damaged or collapsed pipes.
       - Inspect mufflers for heat distress or possible internal failure.
       - For possible plugged three-way catalytic converter. Refer to Restricted Exhaust in Engine Exhaust.
    •  An engine miss condition can be caused by electromagnetic interference (EMI) on the reference circuit. EMI can usually be detected by monitoring engine RPM with a scan tool. A sudden increase in RPM with little change in actual engine RPM change, indicates EMI is present. If a condition exists, check routing of secondary ignition wires, high voltage components, near ignition control circuits.
    • Check for intake and exhaust manifold passages for casting flash.
    • Check for faulty motor mounts. Refer to Engine Mount Inspection in Engine Mechanical.