Component Specifications Front
Application | Specification | |
|---|---|---|
Metric | English | |
Front Disc Brake Inner And Outer Pads | ||
Disc Pad Material | -- | Semi-metallic, Non-asbestos |
Wear Sensor | -- | Electronic |
Approximate Thickness of New Brake Lining with Lining Plate | 17.5 +/- 0.6 mm | 0.688" +/- 0.023" |
Minimum Remaining Thickness Including Lining Plate | 8 mm | 0.315" |
Minimum Taper | 0.15 mm | 0.006" |
Front Brake Caliper | ||
Type | -- | Single Cylinder, Sliding Caliper |
Caliper Bore Diameter | 57.0 mm | 2.244" |
Front Brake Rotor | ||
Type | -- | Vented |
Diameter (Nominal) | 296 mm | 11.653" |
Maximum Lateral Runout (Installed) | 0.16 mm | 0.004" |
Maximum Lateral Runout (Removed) | 0.04 mm | 0.001" |
Thickness (New) | 28 mm | 1.102" |
Maximum Thickness Variation | 0.02 mm | 0.0005" |
Minimum Thickness after Refinish | 26.5 mm | 1.043" |
Discard Thickness * All front brake rotors have a discard dimension cast in them. This is a wear dimension and not a refinish dimension. Any front brake rotor which does not meet the specification should be replaced. | 25 mm | 0.984" |
Rotor Refinishing Specifications Ammco® Brake Lathe Rough Cut | ||
Spindle Speed | -- | 150 rpm |
Depth of Cut (per side) | 0.15 to 0.64 mm | 0.006" to 0.025" |
Tool Crossfeed (per revolution) | 0.25 mm | 0.010" |
Minimum Remaining Thickness Including Lining Plate | 8 mm | 0.315" |
Vibration Dampener | -- | Yes |
Sand Front Brake Rotor (Swirl Pattern) | -- | No |
Finish Cut | ||
Spindle Speed | -- | 150 rpm |
Depth of Cut | 0.10 to 0.15 mm | 0.004" to 0.006" |
Tool Crossfeed (per revolution) | 0.05 mm | 0.002" |
Vibration Dampener | -- | Yes |
Sand Front Brake Rotor (Swirl Pattern) | -- | Yes |
Accuturn® Brake Lathe Single Cut | ||
Spindle Speed | -- | 105 rpm |
Depth of Cut | -- | As necessary |
Tool Crossfeed (per revolution) | 0.08 mm | 0.003" |
Vibration Dampener | -- | Yes |
Sand Front Brake Rotor (Swirl Pattern) | -- | Yes |
Component Specifications Rear
Application | Specification | |
|---|---|---|
Metric | English | |
Rear Brake Caliper Piston Bore Diameter | 40 mm | 1.574" |
Rear Brake Rotor Diameter (Nominal) | 286 mm | 11.259" |
Rear Brake Rotor Lateral Runout (On-Vehicle) | 0.10 mm | 0.004" |
Maximum Thickness Variation | 0.0013 mm | 0.0005" |
Rear Brake Rotor Thickness (New) | 12 mm | 0.472" |
Minimum Thickness After Refinish | 11 mm | 0.433" |
Discard Thickness | 10 mm | 0.393" |
Maximum Taper All rear brake rotors have a discard dimension cast into them. This is a wear dimension and not a refinish dimension. Any rear brake rotor which does not meet this specification should be replaced. | 0.15 mm | 0.006" |
Rotor Refinishing Specifications Ammco Brake Lathe Rough Cut | ||
Spindle Speed | -- | 150 rpm |
Depth of Cut (Per Side) | 0.15 to 0.64 mm | 0.006" to 0.025" |
Tool Crossfeed (Per Rev.) | 0.25 mm | 0.010" |
Vibration Dampener | -- | Yes |
Sand Brake Rotor (Swirl Pattern) | -- | No |
Finish Cut | ||
Spindle Speed | -- | 150 rpm |
Depth of Cut (Per Side) | 0.10 to 0.15 mm | 0.004" to 0.006" |
Tool Crossfeed (Per Rev.) | 0.05 mm | 0.002" |
Vibration Dampener | -- | Yes |
Sand Brake Rotor (Swirl Pattern) | -- | Yes |
Accuturn Brake Lathe Single Cut Refinishing | ||
Spindle Speed | -- | 105 rpm |
Depth of Cut | -- | As necessary |
Tool Crossfeed (Per Rev.) | 0.08 mm | 0.003" |
Vibration Dampener | Yes | Yes |
