DTC B1316 In Car Temperature Sensor Open Circuit. Cadillac Eldorado 1998

For 1990-2009 cars only

Makes 🢒 Cadillac 🢒 1998 🢒 Eldorado 🢒 HVAC 🢒 HVAC Systems - Automatic 🢒 DTC B1316 In Car Temperature Sensor Open Circuit

HVAC Components
Cell 68: Temperature Sensors
Handling ESD Sensitive Parts Notice
Power Distribution Schematics
Power Distribution Schematics
HVAC Compressor Control Schematics

Circuit Description

The inside air temperature sensor is a thermistor that controls the signal voltage to the heater and A/C programmer. The heater and A/C programmer supplies voltage on CKT 734. When the sensor is cold, the following conditions exist:

•	The resistance is high.

•	The heater and A/C programmer reads a high signal voltage at pin D9.

As the sensor warms, the following actions occur:

•	The resistance decreases.

•	The signal voltage is pulled low through the sensor ground, CKT 407.

The signal voltage varies between 5 V (open circuit) and 0 V (short circuit).

Conditions for Running the DTC

•	Turn the ignition to the ON position.

•	The ambient air temperature reads above -29°C (-20°F).

•	DTCs B1310 or B1311 are not set.

Action Taken When the DTC Sets

A substitute temperature reading of 24°C (75°F) is used in order to continue the operation. As a result, the internal temperature may be overly warm or overly cold.

Notes On Intermittence

If an intermittent DTC B1316 is set, use a Scan Tool in order to select the following settings:

•

Data list

•	Open/shorts data

•	Observe the reading

Manipulate the wiring while observing the Scan Tool . If a failure is induced, the reading will jump. Inspect for the following conditions:

•	Faulty terminal contact

•	An obstructed or defective sensor

Test Description

Perform the Diagnostic System Check before continuing with the diagnosis of this DTC.

The Scan Tool displays the inside air temperature. Jumping the harness connector determines if the wiring or the sensor is the cause.

Step	Action	Value(s)	Yes	No
1	Did you perform the Diagnostic System Check?	--	Go to Step 2	Go to Diagnostic System Check
2	Turn the ignition to the ON position. Connect a Scan Tool . Disconnect the in car temperature sensor. Attach a jumper between terminal B and terminal A. Did the DTC change from B1316 to B1317?	--	Go to Step 4	Go to Step 3
3	Measure the voltage at terminal B. Refer to Measuring Voltage in Wiring Systems. Is the measured voltage approximately equal to the specified value?	5 V	Go to Step 6	Go to Step 5
4	Replace the sensor. Refer to Inside Air Temperature Sensor Replacement . Use the Scan Tool in order to clear the codes. Did you complete the repair?	--	System OK	--
5	Measure the voltage at terminal D9 of the heater and A/C programmer. Refer to Measuring Voltage in Wiring Systems. Is the measured voltage approximately equal to the specified value?	5 V	Go to Step 8	Go to Step 7
6	Repair the open in CKT 407 between terminal A and S217. Refer to Wiring Repairs in Wiring Systems. Use the Scan Tool in order to clear the code. Did you complete the repair?	--	Go to Diagnostic System Check	--
7	Inspect the terminal contact. Refer to Testing for Electrical Intermittents in Wiring Systems. If the contact is OK, replace the heater and A/C programmer. Refer to Programmer Replacement . Use the Scan Tool in order to clear the code. Did you complete the repair?	--	Go to Diagnostic System Check	--
8	Measure the voltage at cavity C of C205. Refer to Measuring Voltage in Wiring Systems. Is the measured voltage approximately equal to the specified value?	5 V	Go to Step 10	Go to Step 9
9	Repair the open in CKT 734 between the heater and A/C programmer and C203. Refer to Wiring Repairs in Wiring Systems. Use the Scan Tool in order to clear the code. Did you complete the repair?	--	Go to Diagnostic System Check	--
10	Repair the open in CKT 734 between C203 and the sensor. Refer to Wiring Repairs in Wiring Systems. Use the Scan Tool in order to clear the code. Did you complete the repair?	--	Go to Diagnostic System Check	--