Did you perform the Fuel filler door Release Inoperative System Check?

Go to Step 2

Go to Fuel Filler Door Release System Check

1. Place the transaxle in the PARK position.
2. Turn the valet switch OFF.
3. Connect the Scan Tool .
4. Press the fuel door release switch.

Does the body control module (PZM) turn on the fuel door release?

--

Go to Step 3

Go to Step 7

1. Disconnect the fuel door release relay center #3.
2. Connect a test lamp between terminal D7 and ground, and terminal D9 to ground.

Does the test lamp light at both terminals?

--

Go to Step 4

Go to Step 14

1. Connect the test lamp between terminal D7 and terminal D9.
2. Press the fuel door release switch.

Does the test lamp light?

--

Go to Step 5

Go to Step 15

Connect a fused jumper between terminal D9 and terminal C7.

Does the fuel door open?

--

Go to Step 6

Go to Step 16

Replace the fuel door release relay.

Does the fuel door release operate properly?

--

Go to Fuel Filler Door Release System Check

Go to Step 7

Observe the Scan Tool .

Does the PZM indicate that the valet switch is OFF?

--

Go to Step 8

Go to Step 11

Using the Scan Tool , observe the status of the park neutral position switch.

Does the status show that the vehicle is in PARK?

--

Go to Step 9

Go to Step 10

Replace the PZM. Refer to Body Control Module Replacement in Body Control System.

Does the fuel door release operate properly?

--

Go to Fuel Filler Door Release System Check

Go to Step 11

1. Inspect the PARK NEUTRAL position switch and any related circuits.
2. Perform any necessary repairs.

Does the fuel door release operate properly?

--

Go to Fuel Filler Door Release System Check

Go to Step 11

1. Disconnect the valet switch.
2. Connect a fused jumper from valet switch connector terminal A to ground.
3. Observe the Scan Tool .

Does the PZM indicate that the valet switch is OFF?

--

Go to Step 12

Go to Step 13

1. Inspect CKT 151 (BLK) for an open. Repair the circuit, if necessary.
2. If CKT 151 is OK, replace the valet lockout switch.

Does the fuel door release operate properly?

--

Go to Fuel Filler Door Release System Check

Go to Step 16

1. Inspect CKT 1355 (DK BLU/WHT) for an open. Repair the circuit, if necessary.
2. If CKT 1355 is OK, replace the valet lockout switch.

Does the fuel door release operate properly?

--

Go to Fuel Filler Door Release System Check

Go to Step 16

Repair the open or the short to ground in one of the following circuits:

Does the fuel door release operate properly?

--

Go to Fuel Filler Door Release System Check

Go to Step 16

1. Inspect CKT 93 for an open. Repair the circuit, if necessary.
2. If CKT 93 is OK, replace the PZM. Refer to Body Control Module Replacement in Body Control System.

Does the fuel door release operate properly?

--

Go to Fuel Filler Door Release System Check

Go to Step 16

1. Verify that the fused jumper is still connected.
2. Disconnect the fuel door release solenoid.
3. Connect a test lamp between terminal A and ground.

Does the test lamp light?

--

Go to Step 17

Go to Step 20

1. Verify that the fused jumper is still connected.
2. Connect a test lamp between the fuel door release solenoid terminal A and terminal B.

Does the test lamp light?

--

Go to Step 18

Go to Step 19

1. Verify that the fuel door release solenoid connector is clean and tight.
2. If the connector is OK, replace the fuel door release solenoid.

Does the fuel door release operate properly?

--

Go to Fuel Filler Door Release System Check

--

Repair the open in CKT 1150 (BLK).

Does the fuel door release operate properly?

--

Go to Fuel Filler Door Release System Check

--

Repair the open in CKT 79 (PNK).

Does the fuel door release operate properly?

--

Go to Fuel Filler Door Release System Check

--