GM Service Manual Online
For 1990-2009 cars only
Makes šŸ¢’ Chevrolet šŸ¢’ 2001 šŸ¢’ Astro - 2WD šŸ¢’ Restraints šŸ¢’ SIR šŸ¢’ Ignition Lock Cylinder Replacement - On Vehicle

Removal Procedure

    Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

  1. Disconnect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.

    2. Caution: This vehicle is equipped with a Supplemental Inflatable Restraint (SIR) System. Failure to follow the correct procedure could cause the following conditions:

       ā€¢ Air bag deployment
       ā€¢ Personal injury
       ā€¢ Unnecessary SIR system repairs
    In order to avoid the above conditions, observe the following guidelines:
       ā€¢ Refer to SIR Component Views in order to determine if you are performing service on or near the SIR components or the SIR wiring.
       ā€¢ If you are performing service on or near the SIR components or the SIR wiring, disable the SIR system. Refer to Disabling the SIR System.

  2. Disable the SIR system. Refer to Disabling the SIR System in SIR.
  3. Remove the lower steering column trim cover. Refer to Steering Column Trim Covers Replacement - On Vehicle .

    4. Object Number: 415299 Size: SH
  4. Remove the upper steering column trim cover mounting screws (1).
  5. Lift the upper steering column trim cover to gain access to the lock cylinder access hole.

    6. Object Number: 375310 Size: SH
  6. Using a bent tip awl, insert the tip into the ignition lock cylinder access hole.

    7. Object Number: 375316 Size: SH
  7. Turn the ignition lock cylinder to the START position.

    8. Using the bent tip awl, push down on the ignition lock cylinder retaining pin.

  8. Release the ignition lock cylinder to the RUN position.

    9. Object Number: 375305 Size: SH
  9. Remove the ignition lock cylinder from the lock module by pulling the ignition lock cylinder away from the steering column.

Installation Procedure

    Object Number: 375309 Size: SH
  1. Insert the ignition lock cylinder through the upper steering column trim cover.
  2. Install the ignition lock cylinder to the lock module by performing the following steps:
    3. 2.1. Align the positioning slot and locking tab slot on the lock module to the positioning tab and locking tab on the ignition lock cylinder.
    2.2. Push the ignition lock cylinder into the lock module until the locking tab locks against the lock module.

    Object Number: 415299 Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the upper steering column trim cover mounting screws (1).

    4. Tighten
    Tighten the upper steering column trim cover mounting screws (1) to 1.5 NĀ·m (31 lb in).

  4. Install the lower steering column trim cover. Refer to Steering Column Trim Covers Replacement - On Vehicle .
  5. Enable the SIR system. Refer to Enabling the SIR System in SIR.
  6. Connect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.