Daytime Running Lamps (DRL) Headlamps Always On Standard
Step | Action | Value(s) | Yes | No | ||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | Did you perform the Lighting Systems Diagnostic System Check? | -- | Go to Step 2 | |||||||||||||||||||||
2 | Verify that the DRL headlamps are always on. Do the DRL headlamps operate normally? | -- | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 3 | ||||||||||||||||||||
3 | Use the Scan Tool to inspect for the following related Body Control Module (BCM) Data/ Input parameters and Output controls. Refer to Scan Tool Data List in Body Control System for typical values and definitions.
Did you find and correct a problem? | -- | Go to Step 9 | Go to Step 4 | ||||||||||||||||||||
4 | Remove the DRL relay from the underhood fuse block. Do the daytime running lamps remain on? | -- | Go to Step 5 | Go to Step 6 | ||||||||||||||||||||
5 | Locate and repair a short to ground in CKT 711 (DK GRN/WHT) between the left headlamp high beam bulb and the underhood fuse block. Refer to Wiring Repairs in Wiring Systems. Is the repair complete? | -- | Go to Step 9 | -- | ||||||||||||||||||||
6 |
Is continuity present? | -- | Go to Step 7 | Go to Step 8 | ||||||||||||||||||||
7 | Locate and repair short to ground in CKT 592 (LT GRN/BLK). Refer to Wiring Repairs in Wiring Systems. Is the repair complete? | -- | Go to Step 9 | -- | ||||||||||||||||||||
8 | Replace the DRL Relay. Is the repair complete? | -- | Go to Step 9 | -- | ||||||||||||||||||||
9 | Operate the system in order to verify the repair. Did you correct the condition? | -- | System OK | Go to Step 3 |
Daytime Running Lamps (DRL) Headlamps Always On Envoy/Diamond Edition 1SK
Step | Action | Value(s) | Yes | No | ||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | Did you perform the Lighting Systems Diagnostic System Check? | -- | Go to Step 2 | |||||||||||||||||||||
2 | Verify that the DRL headlamps are always on. Do the DRL headlamps operate normally? | -- | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 3 | ||||||||||||||||||||
3 | Use the Scan Tool to inspect for the following related Body Control Module (BCM) Data/ Input parameters and Output controls. Refer to Scan Tool Data List in Body Control System for typical values and definitions.
Did you find and correct a problem? | -- | Go to Step 9 | Go to Step 4 | ||||||||||||||||||||
4 | Remove the DRL relay from the underhood fuse block. Do the daytime running lamps remain on? | -- | Go to Step 5 | Go to Step 6 | ||||||||||||||||||||
5 | Locate and repair a short to power in CKT 1193 (LT GRN/BLK) between the right headlamp high beam bulb and the underhood fuse block. Refer to Wiring Repairs in Wiring Systems. Is the repair complete? | -- | Go to Step 9 | -- | ||||||||||||||||||||
6 |
Is continuity present? | -- | Go to Step 7 | Go to Step 8 | ||||||||||||||||||||
7 | Locate and repair short to ground in CKT 592 (LT GRN/BLK). Refer to Wiring Repairs in Wiring Systems. Is the repair complete? | -- | Go to Step 9 | -- | ||||||||||||||||||||
8 | Replace the DRL Relay. Is the repair complete? | -- | Go to Step 9 | -- | ||||||||||||||||||||
9 | Operate the system in order to verify the repair. Did you correct the condition? | -- | System OK | Go to Step 3 |
Daytime Running Lamps (DRL) Headlamps Always On ZR2
Step | Action | Value(s) | Yes | No | ||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | Did you perform the Lighting Systems Diagnostic System Check? | -- | Go to Step 2 | |||||||||||||||||||||
2 | Verify that the DRL headlamps are always on. Do the DRL headlamps operate normally? | -- | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 3 | ||||||||||||||||||||
3 | Use the Scan Tool to inspect for the following related Body Control Module (BCM) Data/ Input parameters and Output controls. Refer to Scan Tool Data List in Body Control System for typical values and definitions.
Did you find and correct a problem? | -- | Go to Step 9 | Go to Step 4 | ||||||||||||||||||||
4 | Remove the DRL (ZR2) relay. Do the daytime running lamps remain on? | -- | Go to Step 5 | Go to Step 6 | ||||||||||||||||||||
5 | Locate and repair short to ground in CKT 525 (YEL). Refer to Wiring Repairs in Wiring Systems. Is the repair complete? | -- | Go to Step 9 | -- | ||||||||||||||||||||
6 |
Is continuity present? | -- | Go to Step 7 | Go to Step 8 | ||||||||||||||||||||
7 | Locate and repair short to ground in CKT 592 (LT GRN/BLK). Refer to Wiring Repairs in Wiring Systems. Is the repair complete? | -- | Go to Step 9 | -- | ||||||||||||||||||||
8 | Replace the DRL Relay. Is the repair complete? | -- | Go to Step 9 | -- | ||||||||||||||||||||
9 | Operate the system in order to verify the repair. Did you correct the condition? | -- | System OK | Go to Step 3 |
