Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: Exterior Lights Schematics Connector End View Reference: Master Electrical Component List in Wiring Systems | |||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information |
2 |
Do the appropriate turn signal lamps and/or indicators illuminate for each action? | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 3 |
3 | Is only one turn signal lamp inoperative? | Go to Step 6 | Go to Step 4 |
4 | Is one or both of the turn signal indicators inoperative? | Go to Step 5 | Go to Step 7 |
5 |
Does the appropriate turn signal indicator illuminate and flash? | Go to Step 13 | Go to Step 11 |
6 |
Does the test lamp illuminate and flash? | Go to Step 14 | Go to Step 15 |
7 | Do the hazard lamps operate properly? | Go to Step 8 | Go to Hazard Lamps Inoperative |
8 |
Do the left turn lamps illuminate and flash? | Go to Step 9 | Go to Step 10 |
9 | Connect the 3-amp fused jumper wire between the left turn signal switch signal circuit of the turn signal/multifunction switch and the ground circuit of the turn signal/multifunction switch. Do the left turn lamps illuminate and flash? | Go to Step 12 | Go to Step 16 |
10 | Test the left turn signal switch signal circuit for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 20 | Go to Step 13 |
11 | Inspect for poor connections at the harness connector of the IPC. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 20 | Go to Step 17 |
12 | Inspect for poor connections at the harness connector of the turn/headlamp/wiper switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 20 | Go to Step 18 |
13 | Inspect for poor connections at the harness connector of the body control module (BCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 20 | -- |
14 | Repair an open or high resistance in the ground circuit of the inoperative lamp. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you complete the repair? | Go to Step 20 | -- |
15 | Repair an open, high resistance, or short to ground in the inoperative turn signal supply voltage circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you complete the repair? | Go to Step 20 | -- |
16 | Repair an open or high resistance in the ground circuit of the turn signal/multifunction switch. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you complete the repair? | Go to Step 20 | -- |
17 | Replace the IPC. Refer to Instrument Cluster Replacement in Instrument Panel, Gages, and Console. Did you complete the replacement? | Go to Step 20 | -- |
18 | Replace the turn signal/multifunction switch. Refer to Turn Signal Multifunction Switch Replacement in Steering Wheel and Column. Did you complete the replacement? | Go to Step 20 | -- |
19 |
Important: After replacing the BCM, perform the setup procedure. Refer to Body Control Module (BCM) Programming/RPO Configuration in Computer/Integrating Systems. Replace the BCM. Refer to Body Control Module Replacement in Computer/Integrating Systems. Did you complete the replacement? | Go to Step 20 | -- |
20 | Operate the system in order to verify the repair. Did you correct the condition? | System OK | Go to Step 3 |
