DTC P1861 Non-Europe or N. American Emissions
Circuit Description
The pressure control valves 3, 4, 5, and 6 are precision electronic pressure regulators that control the operation of the clutches, brakes, and lock-up clutch.
The valve reduces the system pressure with which the downstream solenoid valves and electrical pressure regulating valves are supplied. It is possible to use smaller solenoid valves as a result. The pressure control valves require a constant input pressure.
Conditions for Setting the DTC
| • | Output voltage of the solenoid valve 4 is less than 2 volts. |
| • | No DTC P1862, P1863. |
| • | Immediately after the above condition occurs |
Action Taken When the DTC Sets
| • | The hold lamp will blink. |
| • | The transmission control module (TCM) will record operating conditions at the time the diagnostic fails. This information will be stored in the Failure Records buffer. |
| • | Adopt Emergency/Substitute mode and constant 4th gear by hydraulic control. |
| • | After ignition OFF/ON: 3rd gear by hydraulic control. P, R, and N also possible. |
| • | Power supply cut off to the pressure control solenoid valve. |
Conditions for Clearing the Hold Lamp/DTC
| • | The hold lamp will turn OFF when the malfunction has not occurred after 3 ignition cycles. |
| • | A history DTC will clear after 40 consecutive warm-up cycles without a fault. |
| • | Using a scan tool can clear history DTCs. |
Diagnostic Aids
When DTC P1861 sets, the possible cause of fault could be the pressure control valve 4.
Step | Action | Values | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |
2 |
Does the valve change ON/OFF? | -- | Go to Diagnostic Aids | Go to Step 3 |
3 |
Is the resistance within the specified value? | TFT 25°C (77°F) 6 ohms | Go to Step 7 | Go to Step 4 |
4 |
Is the resistance within the specified value? | ∞ | Go to Step 6 | Go to Step 5 |
5 | Repair the internal line for valve 4 for a short to ground. Is the repair complete? | -- | System OK | -- |
6 | Replace solenoid valve 4. Is the replacement complete? | -- | System OK | -- |
7 |
Is the resistance within the specified value? | ∞ | Go to Step 9 | Go to Step 8 |
8 | Repair the transaxle wiring harness for a short to ground. Is the repair complete? | -- | System OK | -- |
9 | Replace the TCM. Refer to Transmission Control Module Replacement . Is the replacement complete? | -- | Go to Step 10 | -- |
10 |
Has the last test failed or is the current DTC displayed? | -- | Go to Step 2 | System OK |
DTC P1861 European and N. American Emissions
Circuit Description
The pressure control valves 3, 4, 5, and 6 are precision electronic pressure regulators that control the operation of the clutches, brakes, and lock-up clutch.
The valve reduces the system pressure with which the downstream solenoid valves and electrical pressure regulating valves are supplied. It is possible to use smaller solenoid valves as a result. The pressure control valves require a constant input pressure.
Conditions for Setting the DTC
| • | Output voltage of the solenoid valve 4 is less than 2 volts. |
| • | No DTC P1862, P1863. |
| • | Immediately after the above condition occurs |
Action Taken When the DTC Sets
| • | The malfunction indicator lamp (MIL) will illuminate. |
| • | The transmission control module (TCM) will record operating conditions at the time the diagnostic fails. This information will be stored in the Failure Records buffer. |
| • | Adopt Emergency/Substitute mode and constant 4th gear by hydraulic control. |
| • | After ignition OFF/ON: 3rd gear by hydraulic control. P, R, and N also possible. |
| • | Power supply cut off to the pressure control solenoid valve. |
Conditions for Clearing the MIL/DTC
| • | The MIL will turn OFF when the malfunction has not occurred after 3 ignition cycles. |
| • | A history DTC will clear after 40 consecutive warm-up cycles without a fault. |
| • | Using a scan tool can clear history DTCs. |
Diagnostic Aids
When DTC P1861 sets, the possible cause of fault could be the pressure control valve 4.
Step | Action | Values | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |
2 |
Does the valve change ON/OFF? | -- | Go to Diagnostic Aids | Go to Step 3 |
3 |
Is the resistance within the specified value? | TFT 25°C (77°F) 6 ohms | Go to Step 7 | Go to Step 4 |
4 |
Is the resistance within the specified value? | ∞ | Go to Step 6 | Go to Step 5 |
5 | Repair the internal line for valve 4 for a short to ground. Is the repair complete? | -- | System OK | -- |
6 | Replace solenoid valve 4. Is the replacement complete? | -- | System OK | -- |
7 |
Is the resistance within the specified value? | ∞ | Go to Step 9 | Go to Step 8 |
8 | Repair the transaxle wiring harness for a short to ground. Is the repair complete? | -- | System OK | -- |
9 | Replace the TCM. Refer to Transmission Control Module Replacement . Is the replacement complete? | -- | Go to Step 10 | -- |
10 |
Has the last test failed or is the current DTC displayed? | -- | Go to Step 2 | System OK |
