Variable Effort Steering Circuit Operation. Chevrolet Tahoe

For 1990-2009 cars only

Makes 🢒 Chevrolet 🢒 1998 🢒 Tahoe - 4WD 🢒 Steering 🢒 Variable Effort Steering 🢒 Variable Effort Steering Circuit Operation

Power Steering Hydraulic System

The electronic variable orifice (EVO) power steering pump is a conventional power steering pump with a power steering (PS) solenoid actuator mounted to the outlet port. When the driving conditions require less hydraulic fluid, a flow control valve restricts the flow of the fluid.

Power Steering Solenoid Actuator

Power Steering Solenoid Actuator Location


(1)	Power Steering Pump
(2)	Power Steering Solenoid Actuator

Electronic Variable Orifice (EVO) Actuator Assembly


(1)	Discharge Fitting
(2)	O-Ring (Small) Seal
(3)	O-Ring (Large) Seal
(4)	Flow Control Valve
(5)	Power Steering Solenoid Actuator

The PS solenoid actuator, mounted in the power steering pump, contains a solenoid operated valve. Discharged fluid passes through an orifice in the solenoid. As the vehicle speed increases, the EVO/Passlock™ module increases the pulse width modulation (PWM) signal to the PS solenoid actuator. Higher current gradually moves the valve further and further into the orifice. This action restricts the passage of the fluid flow through the orifice, reducing the power assist in the steering gear. For diagnosis of the steering system, refer to Power Steering System Test in Power Steering System.

Because the EVO/Passlock™ module sends a variable signal, the PS solenoid actuator provides various levels of the power assist. The EVO system therefore consistently adjusts the power steering assist for changing vehicle speeds and changing driving conditions. For the repair procedures, refer to Power Steering Solenoid Actuator and Discharge Fitting Replacement . For diagnosis, refer to Variable Effort Steering System Check .

Electronic Variable Orifice/Passlock™ Module


(1)	Instrument Panel Carrier
(2)	Electronic Variable Orifice (EVO)/Passlock™ Module

The EVO/Passlock™ module, mounted to the instrument panel carrier underneath the radio, uses the input from the vehicle speed sensor (VSS) and the input from the steering handwheel speed sensor in order to regulate the electrical current to the PS solenoid actuator.

The EVO/Passlock™ module also detects faults with the steering wheel rotation sensor, the PS solenoid actuator, and the associated circuits. When the EVO/Passlock™ module detects a fault, the EVO/Passlock™ module disables the EVO system. Then, the vehicle operates with the maximum power assist, until the driver turns the ignition to the OFF position. When driver restarts the vehicle, the EVO/Passlock™ modules resets and enables the operation of the EVO, until the EVO detects another fault. The EVO/Passlock™ module has fault code member. The EVO/Passlock™ module can pinpoint specific faults. For the repair procedure, refer to Theft Deterrent Module Replacement in Theft Deterrent. For diagnosis, refer to Variable Effort Steering System Check .

Steering Handwheel Speed Sensor

This sensor is mounted in the lower bearing of the steering column. The sensor detects abrupt or evasive steering maneuvers, and signals the EVO/Passlock™ module in order to reduce the steering effort. The faster the driver turns the steering wheel, the quicker the steering wheel rotation sensor generates the signal. For repair procedures, refer to Steering Wheel Position Sensor or Steering Shaft Lower Bearing Replacement . For diagnosis, refer to Variable Effort Steering System Check .

Vehicle Speed Sensor

The vehicle speed sensor (VSS) consists of a permanent magnet generator on the transmission housing or transfer case. The generator sends an electrical signal to the powertrain control module (PCM) on vehicles with diesel engines, or to the vehicle control module (VCM) on vehicles with gasoline engines. The VCM/PCM then calculates the vehicle speed and notifies the EVO/Passlock™ module. For diagnosis, refer to Variable Effort Steering System Check .