GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2009 🢒 Uplander Ext. 🢒 HVAC 🢒 Heating, Ventilation, and Air Conditioning 🢒 Auxiliary HVAC Module Replacement

Special Tools

    • J-39400-A halogen Leak Detector
    • J-38185 Hose Clamp Pliers

Removal Procedure

    Object Number: 1548579 Size: SH

    Note: Cap or tape the open air conditioning (A/C) components immediately in order to prevent system contamination.

  1. Recover the refrigerant. Refer to Refrigerant Recovery and Recharging .
  2. Remove the left rear quarter trim panel.
  3. Drain the cooling system. Refer to Cooling System Draining and Filling .
  4. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
  5. Remove the level ride air compressor. Refer to Air Compressor Replacement .
  6. Remove the auxiliary A/C line block fitting bolt.
  7. Remove the A/C line (1) block fitting.
  8. Remove and discard the sealing washers.
  9. Cap or tape the A/C lines.
  10. Disconnect the auxiliary heater hoses (2) from the heater core pipes using the J-38185 pliers .
  11. Lower the vehicle.

    12. Object Number: 1548551 Size: SH
  12. Remove the auxiliary A/C outlet pillar duct bolts (1).
  13. Remove the auxiliary A/C outlet pillar duct (2).

    14. Object Number: 1548553 Size: SH
  14. Remove the auxiliary A/C outlet duct bolts (1).
  15. Remove the auxiliary A/C outlet duct (2).

    16. Object Number: 882525 Size: SH
  16. Disconnect the auxiliary blower motor electrical connector.
  17. Disconnect the auxiliary blower motor resistor electrical connector.
  18. Disconnect the auxiliary temperature actuator electrical connector.
  19. Remove the HVAC module assembly bolts and nut.
  20. Remove the left power sliding door (PSD) module from the mounting bracket and reposition aside, if equipped.
  21. Remove the HVAC module assembly from the vehicle.
  22. Remove and discard the HVAC module assembly to body seals.

Installation Procedure

    Object Number: 882525 Size: SH
  1. Install new HVAC module assembly to body seals.
  2. Install the HVAC module assembly to the vehicle.

    3. Caution: Refer to Fastener Caution in the Preface section.

  3. Install the HVAC module assembly bolts and the nut and tighten to 10 N·m (89 lb in) .
  4. Install the left PSD module to the mounting bracket.
  5. Connect the auxiliary temperature actuator electrical connector.
  6. Connect the electrical connector to the auxiliary blower motor resistor.
  7. Connect the auxiliary blower motor electrical connector.

    8. Object Number: 1548553 Size: SH
  8. Install the auxiliary A/C outlet duct (2).
  9. Install the auxiliary A/C outlet duct bolts (1) and tighten to 10 N·m (89 lb in) .

    10. Object Number: 1548551 Size: SH
  10. Install the auxiliary A/C outlet pillar duct (2).
  11. Install the auxiliary A/C outlet pillar duct bolts (1) and tighten to 10 N·m (89 lb in) .
  12. Raise and suitably support the vehicle.

    13. Object Number: 1548579 Size: SH
  13. Connect the auxiliary heater hoses (2) to the heater core pipes.
  14. Remove the cap or tape from the A/C lines.
  15. Install the new sealing washers onto the A/C line. Refer to Sealing Washer Replacement .
  16. Install the auxiliary A/C line (1) block fitting bolt and tighten to 20 N·m (15 lb ft) .
  17. Install the level ride air compressor. Refer to Air Compressor Replacement .
  18. Lower the vehicle.
  19. Fill the cooling system. Refer to Cooling System Draining and Filling .
  20. Evacuate and recharge the A/C system. Refer to Refrigerant Recovery and Recharging .
  21. Leak test the fittings of the component using J-39400-A detector .
  22. Install the left rear quarter trim panel.
  23. Refer to Control Module References for programming and setup information.