Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptors
DTC B1516 08: Battery Current Sensor Signal InvalidDTC B1516 66: Battery Current Sensor Wrong Mounting Position
Diagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
5 V Reference | B1405 03, B1516 08 | B1516 08 | B1405 07 | -- |
Signal | B1516 08 | B1516 08 | B1516 08 | B1516 08, B1516 66 |
Low Reference | -- | B1516 08 | -- | -- |
Typical Scan Tool Data
Circuit | Short to Ground | Open | Short to Voltage |
|---|---|---|---|
Operating Conditions: Ignition ON, engine OFF. Headlamps, HVAC, and all accessories Off. Parameter Normal Range: -5 amps to -10 amps | |||
5 V Reference | -59.9 amps | -59.9 amps | -- |
Signal | -59.9 amps | 59.9 amps | 59.9 amps |
Low Reference | -- | 59.9 amps | -- |
Circuit/System Description
The battery current sensor measures the current flowing to or from the battery, and supplies a pulse width modulation (PWM) signal to the BCM. The normal operating range of the current sensor is 5-95 percent duty cycle, with 50 percent duty cycle when there is 0 A. The BCM determines if the signal is out of range or if the polarity is reversed.
Conditions for Running the DTC
B1516 08
The BCM is awake.
B1516 66
| • | The BCM is awake. |
| • | The hood, doors, and rear hatch are closed. |
| • | The engine is not running. |
| • | DTC B1516 08 has run and passed. |
Conditions for Setting the DTC
B1516 08
The battery current sensor signal is less than 4 percent or greater than 96 percent duty cycle for 2 minutes.
B1516 66
The battery current is positive for 2 minutes.
Action Taken When the DTC Sets
The regulated voltage control (RVC) is disabled.
Conditions for Clearing the DTC
The DTC passes when the battery current returns to the normal range for 15 seconds.
Diagnostic Aids
DTC B1516 66 may set if a battery charger is used.
Reference Information
Schematic Reference
Starting and Charging Schematics
Connector End View Reference
Description and Operation
Charging System Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
- Ignition ON, engine OFF, turn off the headlamps and all accessories. Do not connect a battery charger.
- Observe the scan tool Battery Current parameter. The reading should be between -5 and -10 amps, and change with the amount of current draw from the battery.
Circuit/System Testing
B1516 08
- Ignition OFF, disconnect the harness connector at the battery current sensor.
- Ignition OFF and scan tool disconnected, open and close the driver door, and wait 1 minute. Test for less than 5 Ω between the low reference circuit terminal B and ground.
- Ignition ON, test for 4.8-5.2 V between the 5 V reference circuit terminal A and ground.
- Verify the scan tool Battery Current is greater than 50 amps.
- Install a 3 A fused jumper wire between the signal circuit terminal C and the low reference circuit terminal B. Verify the scan tool Battery Current is less than -50 amps.
- If all circuits test normal, replace the battery current sensor.
| ⇒ | If greater than the specified range, test the low reference circuit for an open/high resistance. |
| ⇒ | If less than the specified range, test the 5 V reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, then replace the BCM. |
| ⇒ | If greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit tests normal, then replace the BCM. |
| ⇒ | If less than the specified range, test the signal circuit terminal C for a short to ground. If the circuit tests normal, replace the BCM. |
| ⇒ | If greater than the specified range, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM. |
B1516 66
- Verify the battery current sensor is installed securely around the negative battery cable, and positioned with the tape tab pointing away from the negative terminal of the battery.
- Replace the battery current sensor.
| ⇒ | If the battery current sensor is not installed correctly, remove and reinstall the sensor. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References - for BCM replacement, setup, and programming. |
