| Table 1: | Folding Top Module Scan Tool Data Parameters |
| Table 2: | Folding Top Module Scan Tool Output Controls |
Parameter | System State | Expected Value | Description |
|---|---|---|---|
Operating Conditions: Ignition ON, folding top in fully closed position, vehicle in park, trunk closed, and luggage barrier in place. | |||
Battery Voltage Signal | -- | Varies | The scan tool displays Volts. This displays the current battery voltage signal. |
Folding Top Bell Crank Sw. | -- | Over Center | The scan tool displays Over Center or Not Over Center. This displays the state of S14. |
Folding Top Downstack Receiver Sw. | -- | In Position | The scan tool displays In Position or Not in Position. This displays the state of S13. |
Folding Top Header Dowel Pin | -- | Not in Position | The scan tool displays In Position or Not in Position. This displays the state of S17. |
Folding Top Header Latched | -- | Yes | The scan tool displays Yes or No. This displays the state of S18. |
Full Cycle Counter | -- | Varies | The scan tool displays how many times the folding top has been operated. |
Hall Sensor Feed Status | -- | OK | The scan tool displays OK or No Output. This displays if there is voltage present on the 12 volt reference circuits of S1 and S2. |
Inputs Correct to Start | -- | Yes | The scan tool displays Yes or No. This displays if conditions are correct for folding top operation. |
LF RCL Latched Switch | -- | Active | The scan tool displays Active or Inactive. This displays the state of S12. |
LF RCL Unlatched Switch | -- | Inactive | The scan tool displays Active or Inactive. This displays the state of S11. |
Logic Battery | -- | 12 volts | The scan tool displays the logic voltage of the Folding Top Control Module. |
Luggage Barrier In Place | -- | Yes | The scan tool displays Yes or No. The scan tool displays if the luggage barrier in the rear compartment is in place. |
Motor Command | -- | 0 amps | The scan tool displays the number of amps the Folding Top Pump Motor is operating at. |
Outputs Correct to Start | -- | Yes | The scan tool displays Yes or No. This displays if the outputs are in the proper state for folding top operation. |
Pump Motor Command | -- | Idle | The scan tool displays Idle, A Direction, B Direction, or Error. This displays whether the Folding Top Pump Motor is active and the direction that it is turning when active. |
Pump Over Temperature Sensor | -- | Normal | The scan tool displays Normal or Overtemp. The Folding Top Pump Motor will not run if it is over temperature. |
RCL Front Sw. Ready to Latch | -- | In Position | The scan tool displays In Position or Not in Position. This displays the state of S19A and S19B. |
RCL Release Switch | -- | Unlatched | The scan tool displays Latched, Unlatched, Invalid, or Transition. This displays the state of S3 and S4. |
Rear Compartment Lid Ajar | -- | No | The scan tool displays Yes or No. This displays if the trunk is open. |
RF RCL Latched Switch | -- | Active | The scan tool displays Active or Inactive. This displays the state of S10. |
RF RCL Unlatched Switch | -- | Inactive | The scan tool displays Active or Inactive. This displays the state of S9. |
Too Cold For Top Operation | -- | No | The scan tool displays Yes or No. This displays if it is too cold for the top to operate. |
Top Control Switch | -- | Idle | The scan tool displays Opening, Closing, Invalid, or Idle. This displays the state of the Folding Top Open/Close Switch. |
Valve 1 Command | -- | Off | The scan tool displays On or Off. This displays if Valve 1 is commanded on or off. |
Valve 2 Command | -- | Off | The scan tool displays On or Off. This displays if Valve 2 is commanded on or off. |
Vehicle In Park | -- | Yes | The scan tool displays Yes or No. This displays if the vehicle is in park. |
Window Motor Output | -- | Idle | The scan tool displays Up, Down or Idle. This displays up or down when the windows are being commanded. |
Output Control | Description |
|---|---|
Valve 1 Command | Commands the Folding Top Control Module to activate Valve 1. |
Valve 2 Command | Commands the Folding Top Control Module to activate Valve 2. |
Top Open/Close | Commands the Folding Top Control Module to completely open or completely close the folding top. |
Pump Motor Command | The FTC module commands to operate the pump. The motor should operate in the requested direction. |
Window Motor Output | Commands the Folding Top Control Module to run the driver side and passenger side windows up and down. |
