Removal Procedure
Notice: Cap the fittings and plug the holes when servicing the fuel system in
order to prevent dirt and other contaminants from entering the open
pipes and passages.
Important: Always maintain cleanliness when servicing fuel system components.
- Relieve the fuel system pressure. Refer to
Fuel Pressure Relief
.
- Clean all engine fuel pipe connections.
- Clean areas surrounding the engine fuel pipe connections.
- Disconnect the fuel feed and fuel return pipe quick-connect fittings
in the engine compartment. Refer to
Metal Collar Quick Connect Fitting Service
.
- Disconnect the evaporative
emission (EVAP) purge pipe at the EVAP purge valve.
- Raise and support the vehicle. Refer to
Lifting and Jacking the Vehicle
in General Information.
- Disconnect the fuel return
pipe quick-connect fitting in front of the fuel tank. Refer to
Plastic Collar Quick Connect Fitting Service
.
- Disconnect the fuel feed pipe threaded fitting on the engine-side
of the fuel filter.
- Disconnect the EVAP purge pipe at the fuel filter area.
- Cap the fuel filter and the return pipe as needed to stop any
fuel leakage.
- Note the position of the fuel and EVAP pipes and the fuel and
EVAP pipe attaching hardware for installation.
- Remove the fuel feed, fuel return, and EVAP pipe attaching hardware
and the fuel feed, fuel return, and EVAP pipes.
Notice: Do not attempt to straighten any kinked nylon fuel lines.
Replace any kinked nylon fuel feed or return pipes in order to prevent damage
to the vehicle.
- Inspect the
pipes for bends, kinks and cracks.
- Replace the pipe or pipes as required.
Installation Procedure
Caution: In order to reduce the risk of fire and personal injury observe the
following items:
• | Replace all nylon fuel pipes that are nicked, scratched or damaged
during installation, do not attempt to repair the sections of the nylon fuel
pipes |
• | Do not hammer directly on the fuel harness body clips when installing
new fuel pipes. Damage to the nylon pipes may result in a fuel leak. |
• | Always cover nylon vapor pipes with a wet towel before using a
torch near them. Also, never expose the vehicle to temperatures higher than
115°C (239°F) for more than one hour, or more than 90°C (194°F)
for any extended period. |
• | Apply a few drops of clean engine oil to the male pipe ends before
connecting fuel pipe fittings. This will ensure proper reconnection and prevent
a possible fuel leak. (During normal operation, the O-rings located in the
female connector will swell and may prevent proper reconnection if not lubricated.) |
Important: If fuel line bundle attaching hardware is damaged or broken replace
the bundle hardware.
- Install the new fuel feed, fuel return, or EVAP pipe and the fuel and
EVAP pipe attaching hardware as noted during removal.
- Remove the caps from the fuel filter and the fuel return pipe.
- Connect the fuel return pipe quick-connect fitting in front of
the fuel tank. Refer to
Plastic Collar Quick Connect Fitting Service
.
Notice: Use the correct fastener in the correct location. Replacement fasteners
must be the correct part number for that application. Fasteners requiring
replacement or fasteners requiring the use of thread locking compound or sealant
are identified in the service procedure. Do not use paints, lubricants, or
corrosion inhibitors on fasteners or fastener joint surfaces unless specified.
These coatings affect fastener torque and joint clamping force and may damage
the fastener. Use the correct tightening sequence and specifications when
installing fasteners in order to avoid damage to parts and systems.
- Install the fuel
feed pipe threaded fitting nut to the fuel filter outlet.
Tighten
Tighten the fitting nut to 30 N·m (22 lb ft).
- Connect the EVAP purge pipe at the fuel filter area.
- Verify that all of the fuel pipe bundle clips and fasteners are
properly installed.
- Lower the vehicle.
- Connect the EVAP purge
pipe at the EVAP purge valve.
- Connect the fuel feed
and fuel return pipe quick-connect fittings in the engine compartment. Refer
to
Metal Collar Quick Connect Fitting Service
.
- Connect the negative battery cable. Refer to
Battery Negative Cable Disconnection and Connection
in Engine
Electrical.
- Inspect the fuel system for leaks by performing the following steps:
11.1. | Turn ON the ignition for 2 seconds. |
11.2. | Turn OFF the ignition for 10 seconds. |
11.3. | Turn ON the ignition. |
11.4. | Inspect for fuel leaks. |