Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
Diagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Compass Voltage | 1 | 1 | -- | -- |
Compass LIN 3 | 1 | 1 | 1 | -- |
Compass Ground | -- | 1 | 1 | -- |
1. Compass Malfunction | ||||
Circuit/System Description
The compass module communicates with the body control module (BCM) through the local interconnect network 3 (LIN) data circuit. The instrument panel cluster (IPC) receives compass information from the BCM via the serial data circuit. The IPC displays compass information in the driver information center (DIC).
Diagnostic Aids
| • | Check for aftermarket equipment installed or personal items that could create a magnetic field that could affect the performance of the compass. |
| • | Cycle the ignition before performing the compass magnetic variation adjustment procedure. |
| • | Check that the compass module is properly installed in the vehicle. The embossed arrow on the module should be parallel with the centerline of the vehicle. |
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
Driver Information Center (DIC) Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
Ignition ON, compass ON, verify that there is a correct compass reading on the DIC.
| ⇒ | If the compass is incorrect, refer to Compass Display Is Incorrect. |
| ⇒ | If the compass shows CAL or C, refer to Compass Displays CAL. |
| ⇒ | If the compass is blank, refer to Compass Display Is Blank. |
Circuit/System Testing
Compass Display Is Incorrect
- Adjust or change the compass zone using the world magnetic variation map. Refer to Compass Calibration and Magnetic Variance.
- If the compass is still incorrect, replace the compass module.
| ⇒ | If the compass is still incorrect, perform the compass magnetic variation adjustment procedure. Refer to Compass Calibration and Magnetic Variance. |
Compass Displays CAL
- Perform the compass calibration and magnetic variance (zone) adjustment procedure. Refer to Compass Calibration and Magnetic Variance.
- If the compass still displays CAL or C, replace the compass module.
Compass Display Is Blank
- Ignition OFF, disconnect the harness connector at the compass module.
- Test for less than 5 ohms between the ground circuit terminal 2 and ground.
- Ignition ON, verify that a test lamp illuminates between the voltage circuit terminal 1 and ground.
- Ignition OFF, test for greater than 1 ohm between the compass LIN 3 data circuit terminal 3 and ground.
- Ignition ON, verify that a test lamp does not illuminate between the compass LIN 3 data circuit terminal 3 and ground
- Ignition OFF, disconnect the X4 harness connector at the BCM.
- Test for less than 1 ohm between the compass LIN 3 data circuit terminal 3 to the BCM terminal 6.
- If all circuits test normal, replace the compass module.
| ⇒ | If greater than the specified range, test the ground circuit for a short to voltage or an open/high resistance. |
| ⇒ | If the test lamp does not illuminate, repair the circuit for a short to ground or an open/high resistance. |
| ⇒ | If less than the specified range, test the LIN 3 data circuit for a short to ground. |
| ⇒ | If the test lamp illuminates, test the LIN 3 data circuit for a short to voltage. |
| ⇒ | If greater than the specified range, repair the LIN 3 data circuit for an open/high resistance. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References for the IPC replacement, setup, and programming
