Diagnostic Instructions

DTC Descriptors

DTC P0107: Manifold Absolute Pressure (MAP) Sensor Circuit Low Voltage

DTC P0108: Manifold Absolute Pressure (MAP) Sensor Circuit High Voltage

Diagnostic Fault Information

Circuit	Short to Ground	High Resistance	Open	Short to Voltage	Signal Performance
5-Volt Reference	P0107, P0452, P0532, P0641	P0106, P0107	P0107	P0106, P0108, P0453, P0533, P0641	P0106, P0107
MAP Sensor Signal	P0107	P0106, P0107	P0107	P0108	P0106, P0107, P1101
Low Reference	--	P0106, P0108	P0106, P0108	--	P0106, P0108

Typical Scan Tool Data

MAP Sensor

Circuit	Short to Ground	Open	Short to Voltage
Operating Conditions: Engine running, transmission in Park or Neutral Parameter Normal Range: 20-48 kPa, varies with altitude
5-Volt Reference	0 kPa	0 kPa	127 kPa
MAP Sensor Signal	0 kPa	0 kPa	127 kPa
Low Reference	--	127 kPa	--

Circuit Description

The manifold absolute pressure (MAP) sensor has a 5-volt reference circuit, a low reference circuit, and a signal circuit. The control module supplies 5 volts to the MAP sensor on a 5-volt reference circuit, and provides a ground for the low reference circuit. The MAP sensor provides a voltage signal to the control module on a signal circuit relative to the intake manifold pressure changes.

Conditions for Running the DTC

Conditions for Setting the DTC

P0107

The engine control module (ECM) detects that the MAP sensor voltage is less than 0.20 volt for more than 5 seconds.

P0108

The ECM detects that the MAP sensor voltage is more than 4.80 volts for more than 5 seconds.

Action Taken When the DTC Sets

DTCs P0107 and P0108 are Type B DTCs.

Conditions for Clearing the MIL/DTC

DTCs P0107 and P0108 are Type B DTCs.

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Electrical Information Reference

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Special Tools

Circuit/System Verification

1. Verify that DTC P0641 or P0651 is not set.

⇒	If any of the DTCs are set, refer to DTC P0641 or P0651.

2. Ignition ON, observe the MAP Sensor parameter. The reading should be between 0.20-4.80 volts.
3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the MAP sensor.
2. Ignition OFF for 90 seconds, test for less than 5 ohms between the low reference circuit terminal 2 and ground.

⇒	If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

3. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal 1 and ground.

⇒	If less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM.

⇒	If greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the ECM.

4. Verify the scan tool MAP Sensor parameter is less than 1 kPa.

⇒	If greater than 1 kPa, test the signal circuit terminal 3 for a short to voltage. If the circuit tests normal, replace the ECM.

5. Install a 3A fused jumper wire between the signal circuit terminal 3 and the 5-volt reference circuit terminal 1. Verify the scan tool MAP Sensor parameter is greater than 126 kPa.

⇒	If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM.

6. If the circuits test normal, test or replace the MAP sensor.

Component Testing

Important: You must perform the Circuit/System Testing in order to verify the integrity of the MAP sensor circuits before proceeding with the Component Testing.

Erratic Signal Test

1. Ignition OFF, remove the MAP sensor.
2. Install a 3A fused jumper wire between the 5-volt reference circuit terminal 1 and the corresponding terminal of the MAP sensor.
3. Install a jumper wire between the low reference circuit terminal 2 of the MAP sensor and ground.
4. Install a jumper wire at terminal 3 of the MAP sensor.
5. Connect a DMM between the jumper wire from terminal 3 of the MAP sensor and ground.
6. Ignition ON, with the J 23738-A or J 35555 , slowly apply vacuum to the sensor while observing the voltage on the DMM. The voltage should vary between 0-5.2 volts, without any spikes or dropouts.

⇒	If the voltage reading is erratic, replace the MAP sensor.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.