Conditions for Setting the DTC
A driver select switch input error is detected when both switch inputs (connector pins C5 and C6) are grounded or both are open for more than 3.0 seconds consecutively. If a driver select switch input error is detected, the system will default to the Normal switch setting, activate both position L.E.D.s, and set code 33.
Action Taken When the DTC Sets
- Record driver select switch error.
- Turn on both L.E.D.s.
- Default to Touring setting until a valid switch input combination is detected.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 |
Is the resistance greater than the specified value? | 10 ohms | Go to Step 2 | Go to Step 7 |
2 | Check the resistance in circuit 1435 from the control module to the driver select switch. Is the resistance greater than the specified value? | 10 ohms | Go to Step 3 | Go to Step 4 |
3 | Repair the open circuit condition in circuit 1435. Is the repair complete? | -- | ||
4 | Check the resistance in the circuit from the drivers switch to ground. Is the resistance greater than the specified value? | 10 ohms | Go to Step 5 | Go to Step 6 |
5 | Repair the open circuit condition in circuit 1436. Is the repair complete? | -- | -- | |
6 | Replace the driver select switch. Is the repair complete? | -- | -- | |
7 | Measure the resistance between pins C6 and ground of wiring harness connector. Is the resistance greater than the specified value? | 500 ohms | Go to Step 8 | Go to Step 16 |
8 | Measure the resistance between pins C6 and D16 of wiring harness connector. Is the resistance greater than the specified value? | 500 ohms | Go to Step 10 | Go to Step 9 |
9 | Repair the short in circuit 1434. Is the repair complete? | -- | -- | |
10 |
Is the resistance greater than the specified value? | 10 ohms | Go to Step 11 | Go to Step 19 |
11 | Check the resistance in circuit 1434 from the control module to the driver select switch. Is the resistance greater than the specified value? | 10 ohms | Go to Step 12 | Go to Step 13 |
12 | Repair the open in circuit 1434. Is the repair complete? | -- | -- | |
13 | Check the resistance in the circuit from driver select switch to ground. Is the resistance greater than the specified value? | 10 ohms | Go to Step 14 | Go to Step 15 |
14 | Repair the open in circuit 1436. Is the repair complete? | -- | -- | |
15 | Replace the driver select switch. Is the replacement complete? | -- | -- | |
16 |
Is the resistance greater than the specified value? | 500 ohms | Go to Step 17 | Go to Step 18 |
17 | Replace the driver select switch. Is the replacement complete? | -- | -- | |
18 |
Repair the short in circuit 1434. Is the repair complete? | -- | -- | |
19 | Measure the resistance between pins C5 and ground of the wiring harness connector. Is the resistance greater than the specified value? | 500 ohms | Go to Step 20 | Go to Step 23 |
20 | Measure the resistance between pins C5 and D16 of the wiring harness connector. Is the resistance greater than the specified value? | 500 ohms | Go to Step 21 | Go to Step 22 |
21 | Replace the control module. Refer to Electronic Suspension Control Module Replacement . Is the replacement complete? | -- | -- | |
22 | Repair the short in circuit 1435. Is the repair complete? | -- | -- | |
23 |
Is the resistance greater than the specified value? | 500 ohms | Go to Step 24 | Go to Step 25 |
24 | Replace the driver select switch. Is the replacement complete? | -- | -- | |
25 | Repair the short in circuit 1435. Is the repair complete? | -- | -- |
